MikrofonSensor und TemperaturSenor die zwei Python programme funktionieren. mit den jeweiligen 2 json Datein. Beim TemperaturSensor wird im Terminal keine Wertre ausgegeben aber in der json Datei kann man die Temp und Hum sehen.

lib/python3.11/site-packages/adafruit_blinka/microcontroller/starfive/JH7110/pin.py

@@ -0,0 +1,115 @@
+# SPDX-FileCopyrightText: 2024 Vladimir Shtarev, Jetbrains Research
+#
+# SPDX-License-Identifier: MIT
+"""A Pin class for use with StarFive JH7110."""
+
+import VisionFive.gpio as GPIO
+
+GPIO.setmode(GPIO.BOARD)
+
+
+class Pin:
+    """Pins don't exist in CPython so...lets make our own!"""
+
+    IN = 0
+    OUT = 1
+    LOW = 0
+    HIGH = 1
+    PULL_NONE = 0
+    PULL_UP = 1
+    PULL_DOWN = 2
+
+    id = None
+    _value = LOW
+    _mode = IN
+
+    def __init__(self, number):
+        self.id = number
+
+    def __repr__(self):
+        return str(self.id)
+
+    def __eq__(self, other):
+        return self.id == other
+
+    def init(self, mode=IN, pull=None):
+        """Initialize the Pin"""
+        print(self.id)
+        if mode is not None:
+            if mode == self.IN:
+                self._mode = self.IN
+                GPIO.setup(self.id, GPIO.IN)
+            elif mode == self.OUT:
+                self._mode = self.OUT
+                GPIO.setup(self.id, GPIO.OUT)
+            else:
+                raise RuntimeError("Invalid mode for pin: %s" % self.id)
+        if pull is not None:
+            if self._mode != self.IN:
+                raise RuntimeError("Cannot set pull resistor on output")
+            if pull == self.PULL_UP:
+                GPIO.setup(self.id, GPIO.IN, pull_up_down=GPIO.PUD_UP)
+            elif pull == self.PULL_DOWN:
+                GPIO.setup(self.id, GPIO.IN, pull_up_down=GPIO.PUD_DOWN)
+            else:
+                raise RuntimeError("Invalid pull for pin: %s" % self.id)
+
+    def value(self, val=None):
+        """Set or return the Pin Value"""
+        if val is not None:
+            if val == self.LOW:
+                self._value = val
+                GPIO.output(self.id, val)
+            elif val == self.HIGH:
+                self._value = val
+                GPIO.output(self.id, val)
+            else:
+                raise RuntimeError("Invalid value for pin")
+            return None
+        return GPIO.input(self.id)
+
+
+D7 = Pin(7)
+D11 = Pin(11)
+D12 = Pin(12)
+D13 = Pin(13)
+D15 = Pin(15)
+D16 = Pin(16)
+D18 = Pin(18)
+D22 = Pin(22)
+D24 = Pin(24)
+D26 = Pin(26)
+D27 = Pin(27)
+D28 = Pin(28)
+D29 = Pin(29)
+D31 = Pin(31)
+D35 = Pin(35)
+D36 = Pin(36)
+D37 = Pin(37)
+D38 = Pin(38)
+D40 = Pin(40)
+# I2C
+I2C_SDA = Pin(3)
+I2C_SCL = Pin(5)
+
+# SPI
+SPI_MISO = Pin(21)
+SPI_MOSI = Pin(19)
+SPI_SCLK = Pin(23)
+
+# UART
+UART_TX = Pin(8)
+UART_RX = Pin(10)
+
+# PWM, does not support pwmio
+PWM1 = Pin(32)
+PWM2 = Pin(33)
+
+# ordered as i2cId, SCL, SDA
+i2cPorts = ((0, I2C_SCL, I2C_SDA),)
+
+# ordered as spiId, sckId, mosiId, misoId
+spiPorts = ((0, SPI_SCLK, SPI_MOSI, SPI_MISO),)
+
+# ordered as uartId, txId, rxId
+uartPorts = ((0, UART_TX, UART_RX),)